由江苏英达生产，厂家直接供货价格优势明显，质量可靠，欢迎广大新老客户来电咨询或前来工厂洽谈。 Small blasting room environmental protection and energy saving blasting room Honeycomb type blasting room spiral recovery type blasting room is produced by Jiangsu Yingda. The direct supply of the factory has obvious price advantages and reliable quality. Welcome new and old customers to call us or come to the factory to negotiate. 24-hour hotline: 400-690-2006
I. Composition of the blasting room system:
The blasting room system is mainly composed of the following parts: blasting room body, sand material recovery system, sand and dust separation system, sand blasting system, dust removal system, drive flat car, electrical control system, etc.
Second, the blast cleaning process:
Sand blasting equipment can be used for metal rust layer, residual salt and oxide layer on the surface of heat-treated parts, oxide layer on the surface of rolled parts, oxide layer on the surface of forged parts, oxide layer on the surface of welded parts, molding sand and oxide layer on the surface of castings, The residual dirt and tiny burrs on the surface of the machined parts are treated, and the surface of the old machined parts is treated to remove the surface adhesion layer and reveal the basic color of the substrate;
Sand blasting equipment is used for pre-treatment of workpiece surface coating, and various pre-treatment procedures of electroplating process, brush plating process, spraying process and bonding process in order to obtain active surface and improve the coating, coating and bonding parts. Adhesion
The sand blasting equipment can change the physical and mechanical properties of the workpiece. The sand blasting equipment can change the surface stress state of the workpiece, improve the lubrication conditions of the mating parts, reduce the noise during the movement of the mating parts, harden the surface of the workpiece, and improve the wear resistance and Anti-fatigue strength.
Third, equipment use advantages
The metal parts of the sand blasting equipment are basically not damaged, and the dimensional accuracy will not change; the surface of the parts is not polluted, and the abrasive will not chemically react with the material of the parts; the sand blasting equipment can easily handle the grooves, recesses and other difficult to contact In various parts, abrasives with various particle sizes can be selected for use; The processing cost is greatly reduced, which is mainly reflected in the improvement of the working efficiency of the sand blasting equipment, which can meet a variety of surface finishing requirements; low energy consumption and low cost; sand blasting equipment Does not pollute the environment, eliminating the cost of environmental treatment.
Fourth, the honeycomb floor recycling system
The honeycomb floor recycling system is an important part of the sand blasting room. It adopts an advanced semi-honeycomb floor full recycling design. Considering the large weight of the workpiece, the upper surface of the track is consistent with the floor elevation, and simple foundations need to be produced. Saved infrastructure costs for enterprises.
Fifth, the honeycomb floor recycling system has the following significant advantages:
l Abrasives scattered during the blasting process can be immediately recovered without sand accumulation;
l The fan is used for recycling and dust removal, with simple structure and stable operation; the recycling mechanism has no traditional mechanical transmission such as dragons and hoists, and operates stably and reliably;
l Easy maintenance without maintenance;
l Scientific air flow design, the air is blown into the upper part of the blasting room, the air is sucked in the bottom, and the circulation causes the dust generated by the blasting to enter the separation system together with the sand;
l Honeycomb floor adopts triangular rhombus design, which has high load-bearing capacity.
Six, environmental protection and energy saving blasting room honeycomb type blasting room
1) The structure of the sandblasted room is supported and reinforced by metal structural parts. The wallboard is made of new polystyrene color steel sandwich sound insulation board. The inside and outside of the insulation board are 0.426mm thick color steel plate, and 50mm polystyrene thermal insulation material is filled in the middle. A layer of 3mm thick wear-resistant white rubber plate is fixed inside the blasting room to protect the structure of the blasting room from abrasion and reduce noise during blasting. The wear-resistant rubber plate on the top is fixed by beading, and the four walls are wear-resistant. The rubber plate is fixed by hanging battens for easy replacement. The overall design has wear-resistant protection, noise reduction, and heat insulation functions.
2) There are 10 louvered air inlets on the top of the sand blasting room to meet the required air volume of the sand blasting room (the air inlet is designed with a maze-type noise reduction to effectively reduce the noise emission of the sand blasting). The air inlet guides air evenly to the entire horizontal section of the shot peening chamber, and then moves from top to bottom to make the flow velocity of the horizontal section of the shot peening chamber uniform.
3) The steel structural parts (profiles, steel plates, etc.) used in the equipment are sandblasted, and then sprayed with primer and topcoat. The topcoat color is in accordance with the RAL color standard and meets the customer's requirements for the equipment color (the customer provides a color plate).
4) One end of the sand blasting room is equipped with a set of automatic workpiece entry and exit doors with a size of 4500W × 4500Hmm. The two-way method is adopted. At the same time, a set of safety doors are set on both sides of the room. The size is 900W × 2000Hmm. An observation window is set at a suitable position to observe the blasting situation. All the doors are interlocked to prevent personnel from opening the work door during the blasting process and causing personal injury. Emergency stop buttons are installed on both sides of the interior of the room.
5) On the top of the blasting room are installed 10 metal halide-type lighting lamps produced by PHILIPS Company to ensure that the illuminance in the blasting room is greater than 400 Lux. All the lighting lamps are protected by reinforced glass and glass anti-shatter protection film.
Seven, technical service commitment
1. Our company has passed the ISO9001 international quality management system certification. We carry out all the equipment within the scope of the contract from design, manufacturing, installation, commissioning to acceptance inspection in accordance with the procedures prescribed by the system, and bear all responsibilities. User approval, fully listening to users' opinions and accepting user supervision during the whole process;
2. Our company has rich experience in project contracting, and is able to complete the entire project on time and with high quality to ensure product quality
3. We will send experienced personnel to the site to take charge of construction and installation and participate in commissioning;
4. Our company is responsible for training 1-2 operators for free for users, training content: equipment operation, mechanical and electrical maintenance and answering technical questions raised by users;
5. After the warranty period expires, we will supply all kinds of wearing parts and accessories at a preferential price;
6. We will provide users with the following technical documents:
Electrical schematic diagram, equipment use and maintenance instructions, equipment qualification certificate, acceptance report;
7. The quality warranty period is one year from the date of the formal acceptance of the equipment (signature). If any part is damaged during the warranty period, the user is responsible for the cost of repairing and replacing the accessories. If it is a quality problem, our company will replace it unconditionally within the user-defined time. After the warranty period expires, we will still provide after-sales service for life.
Jiangsu Yingda Machinery Co., Ltd. (formerly Dafeng Foundry Machinery General Factory) was established in 1976. It is a high-tech enterprise integrating R & D, design, manufacturing, sales and installation services. Jiangsu Yingda has been engaged in the research and development and production of surface treatment equipment for 40 years. It mainly produces eight series of products in the mechanical industry such as metal surface cleaning machinery and equipment, and sand processing modeling equipment. Products are widely used in railways, automobiles, ships, construction machinery, metallurgy, military industry, medicine and other fields.
The company took the lead in passing ISO9001: 2008 quality management system certification and ISO14001: 2004 environmental management system certification. With a professional technical team, it has successively obtained 30 product patents such as mesh belt pass type shot blasting machine, new mechanical recycling blasting room, roller pass type heavy steel shot blasting machine and 10 Jiangsu high-tech products. (Note: For details of all product patents and all certificates, please refer to the official website of the enterprise: http://ywl66.com/ or Ali Chengxin Archives )
The company adheres to the tenet of "innovation and intent to build", adheres to the principle of "honesty and responsibility", is committed to using technology to provide customers with a better experience and service, and grows with customers to achieve win-win. The product structure and business scope are diversified, serialized and grouped. The products are exported to all parts of the country, and some are exported to Southeast Asia, West Asia and other places.
Some cooperation customers
Welcome new and old customers to inquire or come to the company for interviews.
Company phone: 0515-83752966
Mobile phone: 13505113250
24-hour customer service hotline: 400-690-2006
Corporate website: http://ywl66.com
http: // www.ydpwj.com
Enterprise Wangpu: http://jsydzj.1688.com/
Business Address: No. 43 Dalong Street, Xituan Town, Dafeng, Yancheng City, Jiangsu Province